@article{Lackner,
  author    = {Lackner, Maximilian},
  title     = {Industrial Engineering Management - THE key skill for the Digital Age},
  series = {The International Journal of Engineering and Science (THE IJES)},
  journal   = {The International Journal of Engineering and Science (THE IJES)},
  subject      = {Management},
  language  = {en}
}
@article{MarklLacknerSchmidetal.,
  author    = {Markl, Erich and Lackner, Maximilian and Schmid, Judith and Faast, Thomas},
  title     = {Mutual Benefits from Entrepreneurship of Non-business University Graduates for Academia and Founders},
  series = {International Academic Journal of Entrepreneurship},
  journal   = {International Academic Journal of Entrepreneurship},
  pages     = {8},
  abstract  = {There is a trend among universities to teach entrepreneurship and support startup initiatives. In this article, the state-ofthe- art in entrepreneurship higher education and university ecosystems of non-business schools is reviewed, and the example of the University of Applied Sciences Technikum Wien, Austria, and one of its startup show cases, Toolsense, is elaborated to understand critical success factors for non-business graduates as founders. The mutual benefits for universities and founders are discussed. In the case of Toolsense and the University of Applied Sciences, narrow band IoT as brought to the University by the startup. Implications on a universities' innovation and portfolio management are highlighted. Concerning startups, the importance of growth financing after initial success is elaborated.},
  subject      = {Entrepreneurship},
  language  = {en}
}
@inproceedings{GonzalezGutierrezTreitlerSpoerketal.,
  author    = {Gonzalez-Gutierrez, Joamin and Treitler, Manuel and Spoerk, Martin and Arbeiter, Florian and Schuschnigg, Stephan and Lammer, Herfried and Lackner, Maximilian and Aburaia, Mohamed and Poszvek, G{\"u}nther and Zhang, Haiguang and Sapkota, Janak and Holzer, Clemes},
  title     = {Carbon fiber reinforced thermoplastics for material extrusion additive manufacturing},
  series = {Conference proceedings of 35th International Conference of the Polymer Processing Society},
  booktitle = {Conference proceedings of 35th International Conference of the Polymer Processing Society},
  pages     = {5},
  abstract  = {In an effort to broaden the engineering applications of material extrusion based additive manufacturing (MEAM), new materials are being developed. Adding carbon-fibers (CF) has been one strategy to increase the mechanical performance of different thermoplastics. One challenge is to determine the amount of CF needed to increase the mechanical performance without affecting the "printability" of the compounds. In this paper, different amounts (10, 15, and 20 vol.\%) of CF were added to recycled polypropylene (rPP) and polyamide 12 (PA12). A compatibilizer was used for rPP, but not for PA12. Filaments for MEAM were extruded from the different compounds and the viscosity as well as the tensile properties were measured and compared to the processed polymeric matrices. It was observed that the viscosities at the angular frequencies relevant for MEAM (100 to 200 rad/s) were not significantly different for rPP+CF compounds, but it was higher for PA12+CF compounds. As expected, the elongation at break significantly decreased with the addition of CF for all compounds. For the composites with an rPP matrix, the Young's modulus and the ultimate tensile strength (UTS) continuously increased as the CF content increased to 20 vol.\%. For PA12-based materials, the Young's modulus and the UTS increased with CF content, but adding more than 15 vol.\% did not further improve these values. Therefore, it was concluded that for PA12 the maximum amount of CF that should be added was 15 vol.\%. Using scanning electron microscopy, it was observed that the CF were homogeneously dispersed in the rPP matrix, but not so well in the PA12 matrix, with fibers being more concentrated towards the rim of the filament. Finally, filaments of rPP, rPP+20CF, PA12 and PA12+15CF were used to print complex geometries by means of MEAM, and it was observed that CF helped to reduce the warpage compared to the unfilled filaments. A potential application of this phenomenon could be the reduction of the bed temperature to develop a more energy efficient MEAM process for semi-crystalline polymers.},
  subject      = {Additive Manufacturing},
  language  = {en}
}
@incollection{LacknerMarklCermak,
  author    = {Lackner, Maximilian and Markl, Erich and Cermak, Corinna},
  title     = {Energy Efficiency Management: State of the Art and Improvement Potential Analysis with Regard to Cargo Transport by Air and Rail},
  series = {Transportation Systems Analysis and Assessment},
  booktitle = {Transportation Systems Analysis and Assessment},
  publisher      = {Fachhochschule Technikum Wien},
  abstract  = {This review article summarizes the state of the art in energy efficiency (EE) management in air and rail cargo transportation. After an introduction, explanations and definitions follow around the topic of energy efficiency. The political framework conditions of the European Union (EU) as well as the associated European Union Emissions Trading System are described. In particular, the drive technologies, CO2 emissions, and fuel-saving options are reviewed.},
  subject      = {Energy},
  language  = {en}
}
@incollection{CermakMarklLackner,
  author    = {Cermak, Corinna and Markl, Erich and Lackner, Maximilian},
  title     = {Energy Efficiency Management: State of the Art and Improvement Potential Analysis with Regard to Cargo Transport by Air and Rail},
  series = {Transportation},
  booktitle = {Transportation},
  publisher = {Intech Open},
  publisher      = {Fachhochschule Technikum Wien},
  subject      = {Transportation},
  language  = {en}
}