TY  - GEN
A1  - Bucher, Christoph Michael
A1  - Aburaia, Mohamed
A1  - Markl, Erich
A1  - Engelhardt-Nowitzki, Corinna
A1  - Lackner, Maximilian
A1  - Gonzales-Gutierrez, J.
A1  - Lammer, Helmuth
T1  - Continuous fiber reinforced freeform 3D printing
KW  - Additive Manufacturing
Y1  - 
ER  - 
TY  - CHAP
A1  - Lackner, Maximilian
A1  - Markl, Erich
A1  - Aburaia, Mohamed
T1  - Cybersecurity Management for (Industrial) Internet of Things: Challenges and Opportunities
T2  - Journal of Information Technology & Software Engineering Keywords
KW  - Security
Y1  - 
ER  - 
TY  - CHAP
A1  - Bucher, Michael
A1  - Aburaia, Mohamed
A1  - Markl, Erich
A1  - Engelhardt-Nowitzki, Corinna
A1  - Lackner, Maximilian
A1  - Gonzalez-Gutierrez, Joamin
A1  - Lammer, Herfried
T1  - Poster Symposium on ADDitive Manufacturing and Innovative Technologies
T2  - Symposium on ADDitive Manufacturing and Innovative Technologies
KW  - Innovative Technologies
KW  - ADDitive
KW  - Manufacturing
Y1  - 2020
ER  - 
TY  - GEN
A1  - Dannereder, Florian
A1  - Engelhardt-Nowitzki, Corinna
A1  - Markl, Erich
A1  - Lackner, Maximilian
A1  - Pachschwöll, Paul Herwig
A1  - Aburaia, Mohamed
A1  - Shooman, Diane
T1  - Development of a 3D-Printed Bionic Hand with Muscle- and Force Control
KW  - Robotics
Y1  - 
ER  - 
TY  - JOUR
A1  - Markl, Erich
A1  - Grünbichler, Hannes
A1  - Lackner, Maximilian
T1  - Cyanobacteria for PHB Bioplastics Production: A Review
JF  - IntechOpen
N2  - Cyanobacteria, or blue-green algae, can be used as host to produce polyhydroxyalkanoates (PHA), which are promising bioplastic raw materials. The most important material thereof is polyhydroxybutyrate (PHB), which can replace the commodity polymer polypropylene (PP) in many applications, yielding a bio-based, biodegradable alternative solution. The advantage from using cyanobacteria to make PHB over the standard fermentation processes, with sugar or other organic (waste)
materials as feedstock, is that the sustainability is better (compare first-generation biofuels with the feed vs. fuel debate), with CO2 being the only carbon source and sunlight being the sole energy source. In this review article, the state of the art of cyanobacterial PHB production and its outlook is discussed. Thirty-seven percent of
dry cell weight of PHB could be obtained in 2018, which is getting close to up to 78% of PHB dry cell weight in heterotrophic microorganisms in fermentation reactors. A good potential for cyanobacterial PHB is seen throughout the literature.
KW  - Bio-based Plastics
KW  - PHB
Y1  - 
ER  - 
TY  - JOUR
A1  - Knapp, Alexander
A1  - Lackner, Maximilian
A1  - Markl, Erich
T1  - Abrasive pads for sustainable and cost-effective industrial and institutional floor cleaning
JF  - International Journal of Advance Engineering and Research
Development
N2  - Industrial and institutional floor cleaning today relies on mechanical action combined with chemicals, which is costly and a burden to the environment. There are floor cleaning pads on the market which claim increased service time due to diamond particles contained in the nonwoven materials. In this study, it was investigated whether cleaning results can also be obtained with hard-particle-coated pads using only water. SiC, diamond and Al 2 O 3 were used with particle sizes between 5 and 125 µm. 5 g/m² of hard particles were applied to the pads in epoxy resin. Weight loss from abrasive cleaning in 500 cycles and gloss increase were measured. Diamond and silicon carbide particles were found to work with pure water, without the need for chemical cleaning agents.
KW  - Floor cleaning
KW  - Mechanical Action
KW  - Chemicals
Y1  - 2018
SN  - 2348-4470
SP  - 84
EP  - 86
ER  - 
TY  - GEN
A1  - Kamravamanesh, Donya
A1  - Pflügl, Stefan
A1  - Lackner, Maximilian
A1  - Herwig, Christoph
T1  - Bioprocess Development for Sustainable poly-β-hydroxybutyrate Production
KW  - Bioplastics
KW  - PHB
KW  - Cyanobacteria
Y1  - 
ER  - 
TY  - JOUR
A1  - Markl, Erich
A1  - Grünbichler, Hannes
A1  - Lackner, Maximilian
T1  - PHB - Bio Based and Biodegradable Replacement for PP: A Review
JF  - Novel Techniques in Nutrition and Food Science
KW  - Bio Degradable
KW  - PHB
KW  - Bio-based Plastics
Y1  - 
VL  - 2
IS  - 2
ER  - 
TY  - BOOK
A1  - de Vries, Sytse
A1  - Markl, Erich
A1  - Lackner, Maximilian
T1  - Energy efficiency management in the shipping industry
KW  - Transportation
KW  - Energy efficiency
Y1  - 
SN  - 978 3 659 71981 3
PB  - Lambert Academic Publishing
ER  - 
TY  - CHAP
A1  - Grünbichler, Hannes
A1  - Engelhardt-Nowitzki, Corinna
A1  - Markl, Erich
A1  - Lackner, Maximilian
A1  - Kreith, Josef
A1  - Bermejo Moratinos, Raúl
A1  - Supancic, Peter
A1  - Danzer, Robert
T1  - Adaptation of a universal testing machine to characterise the material response of multi-layered piezoelectric actuators under fully coupled loading scenarios
T2  - th International Conference on Smart Materials and Structures
KW  - Robotics
Y1  - 2019
PB  - Material Sci Eng 2018 (7)
ER  - 
TY  - GEN
A1  - Grünbichler, Hannes
A1  - Engelhardt-Nowitzki, Corinna
A1  - Markl, Erich
A1  - Lackner, Maximilian
A1  - Kreith, Josef
A1  - Bermejo Moratinos, Raúl
A1  - Supancic, Peter
A1  - Danzer, Robert
T1  - Adaptation of a universal testing machine to characterise the material response of multi-layered piezoelectric actuators under fully coupled loading scenarios
KW  - Robotics
Y1  - 2018
ER  - 
TY  - CHAP
A1  - Dannereder, Florian
A1  - Engelhardt-Nowitzki, Corinna
A1  - Markl, Erich
A1  - Lackner, Maximilian
A1  - Kreith, Josef
A1  - Pachschwöll, Paul Herwig
A1  - Aburaia, Mohamed
A1  - Shooman, Diane
T1  - Development of a 3D-Printed Bionic Hand with Muscle- and Force Control
T2  - Proceedings of the Austrian Robotics Workshop 2018
KW  - Robotics
Y1  - 
ER  - 
TY  - CHAP
A1  - Aburaia, Mohamed
A1  - Lackner, Maximilian
A1  - Grünbichler, Hannes
A1  - Engelhardt-Nowitzki, Corinna
A1  - Markl, Erich
A1  - Lammer, H.
A1  - Zhang, Haiguang
A1  - Wang, J.
A1  - Sapotka, J.
A1  - Janics, T.
A1  - Hailberger, M.
T1  - Freeform-FDM process development using natural fibre reinforced biopolymers
T2  - 2nd International Conference on 3D Prinitng Technology and Innovation March 19-20, 2018 London, UK
KW  - Freeform Printing
KW  - Additive Manufacturing
Y1  - 
ER  - 
TY  - CHAP
A1  - Dannereder, Florian
A1  - Pachschwöll, Paul
A1  - Aburaia, Mohamed
A1  - Markl, Erich
A1  - Lackner, Maximilian
A1  - Engelhardt-Nowitzki, Corinna
A1  - Shooman, Diane
T1  - Development of a 3D-printed Bionic Hand with Muscle- and Force Control
T2  - Austrian Robotics Workshop 2018
KW  - Robotics
KW  - Prosthetics
KW  - 3D-Printing
Y1  - 
ER  -