TY - CHAP A1 - Dannereder, Florian A1 - Pachschwöll, Paul A1 - Aburaia, Mohamed A1 - Markl, Erich A1 - Lackner, Maximilian A1 - Engelhardt-Nowitzki, Corinna A1 - Shooman, Diane T1 - Development of a 3D-printed Bionic Hand with Muscle- and Force Control T2 - Austrian Robotics Workshop 2018 KW - Robotics KW - Prosthetics KW - 3D-Printing Y1 - ER - TY - CHAP A1 - Schneider, Simon A1 - Zelger, Thomas A1 - Tabakovic, Momir T1 - Combining bottom-up and top-down approaches to converge heterogeneous building data into a homogenous, interactive and expandable energy autonomy platform T2 - BauZ! 2018 In Betrieb gesetzt! - Wiener Kongress für zukunftsfähiges Bauen KW - Energy Autonomy Y1 - ER - TY - CHAP A1 - Tabakovic, Momir A1 - van Sark, Wilfried A1 - Louwen, Atse A1 - Weiss, Ingrid A1 - Arancon, Sofia A1 - Makrides, George A1 - Hadjipanayi, Maria A1 - Loucaidou, Eliza T1 - Development of BIPV courseware for students and professionals T2 - Proceeding: Austrian PV Conference KW - Course Material KW - Photovoltaics Y1 - ER - TY - CHAP A1 - Tabakovic, Momir T1 - Direct conversation of waste heat from solid-fuel stove into electric energy using a high temperature thermoelectric generator compared to Bi2Te3 thermoelectric generator T2 - Proceeding: ISEC 2018 KW - Energy Conversion KW - Electricity KW - Waste Heat Y1 - ER - TY - RPRT A1 - Tabakovic, Momir A1 - Fechner, Hubert A1 - Leonhartsberger, Kurt T1 - National Survey Report of PV Power Applications in Austria 2017 T2 - IEA- International Energy Agency KW - Photovoltaics KW - Survey Report Y1 - ER - TY - GEN A1 - Kamravamanesh, Donya A1 - Pflügl, Stefan A1 - Lackner, Maximilian A1 - Herwig, Christoph T1 - Photosynthetic poly-β-hydroxybutyrate accumulation in unicellular cyanobacterium Synechocystis sp. PCC 6714 KW - Bacteria Y1 - 2018 ER - TY - BOOK A1 - Lackner, Maximilian A1 - Grabow, Wilhelm A1 - Stadler, Philipp T1 - Handbook of Online and Near-real-time Methods in Microbiology KW - Microbiology Y1 - 2018 ER - TY - JOUR A1 - Aaliya, Basheer A1 - Sunooj, Kappat Valiyapeediyekkal A1 - Sri Rajkumar, Chillapalli Babu A1 - Navaf, Muhammed A1 - Akhila, Plachikkattu Parambil A1 - Sudheesh, Cherakkathodi A1 - George, Johnsy A1 - Lackner, Maximilian T1 - Effect of Thermal Pretreatments on Phosphorylation of Corypha umbraculifera L. Stem Pith Starch: A Comparative Study Using Dry-Heat, Heat-Moisture and Autoclave Treatments JF - Polymers N2 - Talipot starch, a non-conventional starch source with a high yield (76%) from the stem pith of talipot palm (Corypha umbraculifera L.) was subjected to three different thermal treatments (dry-heat, heat-moisture and autoclave treatments) prior to phosphorylation. Upon dual modification of starch with thermal treatments and phosphorylation, the phosphorous content and degree of crosslinking significantly increased (p ≤ 0.05) and was confirmed by the increased peak intensity of P=O and P–O–C stretching vibrations compared to phosphorylated talipot starch in the FT-IR spectrum. The highest degree of crosslinking (0.00418) was observed in the autoclave pretreated phosphorylated talipot starch sample. Thermal pretreatment remarkably changed the granule morphology by creating fissures and grooves. The amylose content and relative crystallinity of all phosphorylated talipot starches significantly decreased (p ≤ 0.05) due to crosslinking by the formation of phosphodiester bonds, reducing the swelling power of dual-modified starches. Among all modified starches, dry-heat pretreated phosphorylated starch gel showed an improved light transmittance value of 28.4%, indicating reduced retrogradation tendency. Pasting and rheological properties represented that the thermal pretreated phosphorylated starch formed stronger gels that improved thermal and shear resistance. Autoclave treatment before phosphorylation of talipot starch showed the highest resistant starch content of 48.08%. KW - Talipot starch KW - Non-conventional starch Y1 - VL - 13 IS - 3855 ER - TY - JOUR A1 - Haas, Theodor A1 - Markl, Erich A1 - Lackner, Maximilian T1 - Innovative use of waste tyres: Noise-barriers and geoengineering JF - World Journal of Advanced Engineering Technology and Sciences KW - Engineering KW - Wastemanagement Y1 - ER - TY - GEN A1 - Lackner, Maximilian T1 - PBAT - A versatile bioplastics KW - Bioplastics Y1 - 2018 ER - TY - CHAP A1 - Tabakovic, Momir A1 - Otto, Marc-Oliver A1 - Commerell, Walter A1 - Csapo, Csilla A1 - Vermaak, Herman T1 - Increase industry cooperation in post graduate education via OpenLab’s and MobileLab’s in South Africa T2 - Smart Education and e-Learning 2020 N2 - This paper will present the concepts of the EURYDICE project funded by the Erasmus + program. Within this project the focus on renewable energies with the overall goal to enhance employability. The energy generation landscape in South Africa is undergoing a fundamental transition, as the vision of the energy strategy is to contribute to an affordable energy for all. This vision will be supported by innovative labs and portals which will be developed within this project. One of the goals is closing the gap between TVET (Technical and Vocational Education and Training Colleges) studies and diploma study by the definition of industrial experience requirements for University of Technology (UoT) diploma students. This leads to an increased preparedness and “studyability” of UoT diploma students. Industrial stakeholders will be integrated into the process. The project will develop an “Industrial Portal” as a working tool. To increase industry cooperation in post graduate education “OpenLabs” and “MobileLabs” will be developed within the project. It is intended that industry brings industrial problems into the “Labs”, which will then be solved by the students. KW - Mobile Labs KW - Employability KW - Renewable Energy Y1 - SP - 623 EP - 629 PB - Springer Verlag ER - TY - CHAP A1 - Tabakovic, Momir A1 - Würfl, Marlen A1 - Guerra, Eduardo A1 - Gutleder, Miriam T1 - Operating models for PV systems in existing residential building complexes in Vienna – challenges and opportunities T2 - XI International Conference Industrial Engineering and Environmental Protection 2021 (IIZS 2021) N2 - This paper aims to identify challenges and opportunities that are associated with installing PV (Photovoltaic) systems in existing residential building complexes in Vienna. For this purpose, a project-oriented approach was chosen and hence a representative residential building complex in Vienna was chosen and analyzed to demonstrate the challenges that are associated with such projects. Furthermore, a particular focus lies on exploring different operating models that are available when it comes to the execution of such a project. As this paper builds on the rather novel topic of exploring new operating models for installing PV systems on existing residential building complexes in Vienna, many further suggestions for research can be identified that exceed the scope of this paper. KW - Photovoltaics KW - Renewable Energy KW - Urban Areas Y1 - ER - TY - JOUR A1 - Lackner, Maximilian A1 - Ouattara, Ibrahim A1 - Gharae, Norouz Ali A1 - Abolhassani, Raymond T1 - Clean drinking water global scarcity: a review JF - Journal of Water Science and Engineering KW - Water KW - Engineering Y1 - 2020 ER - TY - CHAP A1 - Lackner, Maximilian T1 - Combination of Devulcanization and Reactive Extrusion for Value-Added Rubber Recycling T2 - Webinar on Biopolymers & Bioplastics, Meetings International, KW - Recycling Y1 - 2020 ER - TY - JOUR A1 - Zangl, Sabine A1 - Pingitzer, D. A1 - Lembacher, Harald A1 - Lackner, Maximilian T1 - Carbon footprint reduction in households using professional services – example of laundry cleaning JF - Pubtexto KW - Sustainability Y1 - 2020 ER - TY - BOOK A1 - Lackner, Maximilian T1 - Chemical Engineering Vocabulary: Bilingual KW - Chemical Engineering KW - Language Y1 - 2018 ER - TY - CHAP A1 - Tabakovic, Momir A1 - Schneider, Simon A1 - Laurent, Pierre A1 - Zelger, Thomas A1 - Kerschbaum, Elisabeth A1 - Figl, Hildegund T1 - Korneuburgs way2smart - mobility concept, energy platform and social interaction T2 - Proceedings of the 22nd International Conference on Urban Planning, Regional Development and Information Society (REAL CORP 2017 - PANTA RHEI) KW - Energy Market KW - Energy Consumption KW - Household Y1 - 2018 ER - TY - JOUR A1 - Spitzer-Sonnleitner, Birgit A1 - Kempe, Andre A1 - Lackner, Maximilian T1 - Influence of halide solutions on collagen networks - measurements of physical properties by atomic force microscopy (AFM) JF - Influence of halide solutions on collagen networks KW - Collagen Networks KW - Microscopy Y1 - 2018 ER - TY - CHAP A1 - Bululukova, Darya A1 - Wahl, Harald T1 - Towards a Sustainable Smart Cities Integration in Teaching and Research T2 - Proceedings of the 4th International Conference on Smart Cities and Green ICT Systems - Volume 1: SMARTGREENS, 101-106, 2015, Lisbon, Portugal KW - Smart City Y1 - ER - TY - JOUR A1 - Grasel, Bernhard A1 - Baptista, José A1 - Tragner, Manfred T1 - Supraharmonic and Harmonic Emissions of a Bi-Directional V2G Electric Vehicle Charging Station and Their Impact to the Grid Impedance JF - Energies N2 - Bidirectional electric vehicle supply equipment and charging stations (EVSE) offer new business models and can provide services to the electrical grid. The smart grid lab in Vienna gives unique testing possibilities of future smart grids, as different type of electrical equipment can be operated at a reconstructed, well-known distribution grid. In this work the harmonic and supraharmonic emissions of a bidirectional EVSE are measured according to IEC61000-4-7 and IEC61000-4-30 Ed3 standard as well as the high-frequency grid impedance. In addition, the efficiency and the power factor are determined at various operating points. Although THDi at nominal power (10 kW) is very low and the efficiency and power factor is very high, at low power levels the opposite situation arise. Supraharmonic emissions remain stable independent of the charging/discharging power, and both wideband and narrowband emissions occur. The additional capacitance when connecting the EVSE impacts the high-frequency grid impedance substantially and generates resonance points. KW - power quality KW - V2G KW - supraharmonics Y1 - U6 - http://dx.doi.org/10.3390/en15082920 VL - 15 IS - 8 ER - TY - CHAP A1 - Leonhartsberger, Kurt A1 - Meisel, M. A1 - Picler, M. A1 - Schidler, Susanne A1 - Fotiadis, Lampros A1 - Xypolytou, E. A1 - Werner, Andrea T1 - System relevant Applications for Battery Storage Systems T2 - 33rd Passive Low Energy Architecture Conference (PLEA 2017), Edinburgh, Scotland, Proceedings Vol. III KW - Battery Storage Systems KW - Energy Storage Y1 - ER - TY - CHAP A1 - Illich, Peter A1 - Eder, Gabriele C. A1 - Berger, Karl A. A1 - Ujvári, Gusztáv A1 - Rechberger, P. A1 - Moor, D. A1 - Aichinger, Martin T1 - Comparative Performance Measurements of Identical BIPV-Elements in Different Climatic Environments - A Round Robin Action within the IEA PVPS Task 15 Collaboration T2 - 35th European Photovoltaic Solar Energy Conference and Exhibition KW - Photovoltaics KW - Solar Power Y1 - SN - 3-936338-50-7 ER - TY - JOUR A1 - Zhang, Hang A1 - Yao, Yuan A1 - Ma, Yingxin A1 - Lackner, Maximilian A1 - Jiang, Yunliang T1 - A 3D printing tool-path generation strategy based on the partition of principal stress field for fused filament fabrication JF - The International Journal of Advanced Manufacturing Technology N2 - In order to enhance the strength of 3D-printed parts made of polymer materials and reduce the anisotropy caused by the fused filament fabrication process, this paper proposes an inter-layer interleaved composite path planning method based on the directional partition of the principal stress field. This method not only ensures intra-layer reinforcement under specific working conditions but also increases the strength of the printed part by enhancing the adhesion of adjacent layers through staggered filling between layers. The mechanical performance is improved by 10 to 30% compared to other conventional filling patterns such as the zigzag filling algorithm. Inter-layer interleaved composite enhancement path planning method is suitable for path planning of structures with complex shapes and is easily integrated into existing general computer-aided engineering processes. KW - Principal stress field KW - Anisotropy strength KW - Clustering Y1 - IS - 122 SP - 1719 EP - 1735 ER - TY - JOUR A1 - Wöber, Wilfried A1 - Curto, Manuel A1 - Tibihika, Papius D. A1 - Meulenboek, Paul A1 - Alemayehu, Esayas A1 - Mehnen, Lars A1 - Meimberg, Harald A1 - Sykacek, Peter T1 - Identifying geographically differentiated features of Ethopian Nile tilapia (Oreochromis niloticus) morphology with machine learning JF - PlosONE KW - Machine Learning Y1 - VL - 16 IS - 4 ER - TY - CHAP A1 - Wöber, Wilfried A1 - Tibihika, Papius D A1 - Olaverri-Monreal, Cristina A1 - Mehnen, Lars A1 - Sykacek, Peter A1 - Meimberg, Harald T1 - Comparison of Unsupervised Learning Methods for Natural Image Processing T2 - Biodiversity Information Science and Standards KW - Machine Learning KW - Deep Learning KW - Image Processing Y1 - IS - 3 ER - TY - CHAP A1 - Wöber, Wilfried A1 - Szuegyi, Daniel A1 - Kubinger, Wilfried A1 - Mehnen, Lars T1 - A principal component analysis based object detection for thermal infra-red images T2 - Proceedings of the 55th International Symposium ELMAR KW - Principal Component Analysis KW - Object Detection KW - Infra-Red Camera Y1 - 2019 ER - TY - GEN A1 - Spulak, David A1 - Otrebski, Richard A1 - Kubinger, Wilfried T1 - Object Tracking by Combining Supervised and Adaptive Online Learning through Sensor Fusion of Multiple Stereo Camera Systems KW - Object Tracking Y1 - ER - TY - JOUR A1 - Taghavi, Marziyeh A1 - Taghizadeh, Akbar A1 - Mehmannavaz, Yousef A1 - Hosseinkhani, Ali A1 - Mohammadzadeh, Hamid A1 - Macit, Muhlis A1 - Palangi, Valiollah A1 - Lackner, Maximilian T1 - Degradability of Vicia ervilia Grain Using In Situ and CNCPS Methods, and Model-Based Analysis of Its Ruminal Degradation JF - Fermentation N2 - Using nylon bag techniques, Cornell net carbohydrates and protein systems (CNCPS), and scanning electron microscopy, the authors examined the digestibility and structure of Vicia ervilia (ervil, bitter vetch) after steam flaking, roasting, and microwave processing. During the in situ technique, the samples were incubated at 0, 2, 4, 6, 8, 12, 16, 24, 36, and 48 h. For the description of the ruminal DM (dry matter) and CP (crude protein) degradation kinetics of treated and untreated Vicia ervilia, different models were selected as the best fit for the dry matter (DM) and crude protein (CP) degradation parameters of steam flaked samples. The results showed that both the steam flaking and microwave treatment samples contained high levels of non-protein nitrogen and buffer soluble protein, respectively. In comparison with steam flaking and microwave treatment, roasting decreased and increased the buffer soluble protein and neutral detergent insoluble protein, respectively. The control treatments showed the highest levels of neutral detergent soluble protein and the lowest levels of acid detergent soluble protein. Moreover, steam flaking and roasting decreased and increased the amount of acid detergent insoluble protein, respectively. When using dry heat (microwave and roasting), the acid detergent soluble and insoluble protein fractions were increased. As a result of this experiment, the nitrogen fractions were altered using heat processing. Hence, protein fermented feed and ruminal fermentation conditions can be expressed using these results. KW - Vicia ervilia KW - steam flaking KW - microwave KW - roasting Y1 - U6 - http://dx.doi.org/10.3390/fermentation9050419 VL - 9 IS - 5 ER - TY - JOUR A1 - Ahmadzadeh, Leila A1 - Hosseinkhani, Ali A1 - Palangi, Valiollah A1 - Lackner, Maximilian T1 - Supplementary Feed Additives Can Improve Lamb Performance in Terms of Birth Weight, Body Size, and Survival Rate JF - Animals KW - feed restriction KW - monensin sodium KW - offspring performance Y1 - U6 - http://dx.doi.org/10.3390/ani13060993 IS - 13 / 6 ER - TY - CHAP A1 - Wöber, Wilfried A1 - Aburaia, Mohamed A1 - Olaverri-Monreal, Cristina T1 - Classification of Streetsigns Using Gaussian Process Latent Variable Models T2 - 2019 IEEE International Conference on Connected Vehicles and Expo (ICCVE), Graz, Austria KW - Streetsigns KW - Gaussian KW - Vehicles Y1 - 2020 ER - TY - CHAP A1 - Tabakovic, Momir A1 - Bululukova, Darya A1 - Wahl, Harald T1 - Integrative Secondary Education Programmes and Research in Smart Cities Context T2 - Proceedings of the REAL CORP 2016 KW - Smart City KW - Education Y1 - 2018 ER - TY - JOUR A1 - Muehleisen, Wolfgang A1 - Eder, Gabriele C. A1 - Voronko, Yuliya A1 - Spielberger, Markus A1 - Sonnleitner, Horst A1 - Knöbl, Karl A1 - Ebner, Rita A1 - Ujvari, Gusztáv A1 - Hirschl, Christina T1 - Outdoor detection and visualization of hailstorm damages of photovoltaic plants JF - Renewable Energy KW - Photovoltaics KW - Damage Detection KW - Hailstorms Y1 - 2018 IS - 118 SP - 138 EP - 145 ER - TY - CHAP A1 - Papa, Maximilian A1 - Kaselautzke, David A1 - Radinger, Thomas A1 - Stuja, Kemajl T1 - Development of a safety industry 4.0 production environment T2 - 28th DAAAM International Symposium on Intelligent Manufacturing and Automation KW - Saftey KW - Robotics Y1 - 2020 ER - TY - BOOK A1 - Lackner, Maximilian A1 - Chen, Wei-Ying, A1 - Suzuki, Toshio T1 - Handbook of Climate Change Mitigation and Adaptation KW - Climate Change Y1 - 2018 ER - TY - CHAP A1 - Angel, Nikolaus A1 - Orsolits, Horst A1 - Garcia, Jose T1 - Developing an AR Based Tool for Teaching Motion Analysis on Assembly Tasks T2 - 2022 8th International Conference of the Immersive Learning Research Network (iLRN), 2022 N2 - Engineering education courses look into processes, equipment and people in order to prepare students to tackle problems in their careers. In manufacturing industry, it is important to use virtual manufacturing tools to analyse processes. This includes both equipment and people. Assembly operations can involve human operators. Modular arrangements of predetermined time standards MODAPTS is a predetermined motion time system method used to analyse assembly processes. Augmented reality (AR) is increasingly being used for industrial processes as well as in education. AR application have been used for maintenance training as a useful way to overly digital instructions to a trainee whilst being able to look at a real object. This is potential beneficial for education. This paper presents the evaluation of a prototype to test a predetermined time standards model using an AR application. An evaluation was carried out comparing AR-based instructions in tablet and PC monitor and paper-written instructions. The results of evaluating the prototype encourage their use as an educational tool in engineering courses. KW - Augmented Reality KW - Education Technology KW - Virtual Engineering KW - Assembly Assistance Y1 - SN - 978-1-7348-9952-8 U6 - http://dx.doi.org/10.23919/iLRN55037.2022.9815914 ER -